HD74LSP Specifications: Gate Type: NAND ; Supply Voltage: 5V ; Logic Family: TTL ; Inputs: 8 Details, datasheet, quote on part number: HD74LSP . The semiconductor operations of Mitsubishi Electric and Hitachi were transferred to Renesas. Technology Corporation on April 1st HD74LSP from Renesas Electronics. Find the PDF Datasheet, Specifications and Distributor Information.
|Published (Last):||26 October 2007|
|PDF File Size:||10.12 Mb|
|ePub File Size:||7.30 Mb|
|Price:||Free* [*Free Regsitration Required]|
In addition, the same RAM is used to generate the video display.
This tuning allows the two oscillators to be synchronized at any time except during reset or power-on. Color Burst Signal TP. Therefore, it is up to the microprocessor to produce the necessary FSK signals through the DAC and the proper software. Pin 12 of register B is an input for the memory size. This level is one of the sound inputs to the sound multiplexer. One checksum byte – the sum of all the data bytes dafasheet block type and block length bytes 7.
All of the important CPU bus signals are tied to this connector. Figure shows the keyboard matrix. If greater than that, they are considered to be a space.
I i C26 M-Plastic O. From the computer, the signal is connected ratasheet a balun in the switch box which matches the modulator’s ohm output impedance to a TV f xatasheet ohm antenna input impedance. Whenever a cartridge is inserted into the computer, this input will interrupt BASIC and jump to the program in the cartridge.
When using any or all of the information contained in these materials, including product data, diagrams, datasheett, programs, and algorithms, please be sure to. Mfr ‘ s Part No. Removal of Main PCB 3. The TV antenna is attached directly to the switch box. Datashest memory chip is capable of storingbits 64K x 4any one of which may be accessed at any given time. This allows the center wiper to vary from to 5 volts as the handle is moved.
Six bits of control are used by the DAC to specify a discrete internal analog level. RSC Connector Pinout 48 Two bytes for hd74ls3774p start address of a machine language program hd74lw374p. Following is a list of virtually all of the problems that might be identified on the Color Computer 3: It also provides all of the system timing and device selection.
Additional information may be obtained from the 68B09E data sheet.
The Master Oscillator is divided by eight to give a 3. In this step it is wise to check the obvious. The prior written approval of Renesas Technology Corp. SND – This signal is connected directly to the sound input of the DAC chip and allows cartridge-generated sound signals to dataaheet fed through the TV sound system. The four signals used by the interface are: When servicing any computer, it dataasheet important to distinguish a hardware problem from a software problem.
H Pi] KCJ -?? The phase compa generates a control vol proportion to the phase difference between thes These determine which of the joystick inputs is to be compared against the DAC, as well as which sound source is coupled to the sound output pin according to hd74ls347p table on the next page.
One block type byte: It is used to detect the presence of a cartridge.
HD74LSP 데이터시트(PDF) – Renesas Technology Corp
The printer width is columns. The switch box is connected to the customer’s TV through the ohm twin-lead output. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as i placement of substitutive, auxiliary circuits.
CA2 and CB2 pins 19 and 39 are used as outputs. The master crystal oscillator frequency of the PAL version is There is a small amount of hysteresis built in which provides noise immunity and prevents false triggering of the zero-crossing detector.
Online Electronic Components Shop
If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and. The printer will automatically return the carriage at the end of the line. For this purpose, the internal oscillator circuit of the IC is used. Therefore, although it is technically an 8-bit processor, it has some of the power of the bit machines.
These voltages are defined as follows: The negative voltage is not used anywhere else in the computer. The strain relief on the power cord consists of wrapping the cord around the plastic bosses on the rear side of the unit. Finally, the DAC signal is attenuated and used as the cassette recording signal for data storage. For cartridge detection, the Q clock is connected to the cartridge interrupt pin, which generates an interrupt anytime the cartridge is plugged in and forces the computer to jump to the program in ROM.
There are several ways to determine the “size” of a microprocessor whether it is 8-bit, bit, bit, or whatever. Each of the 6-bit elements in this RAM array is an MMU task register, and the task registers are used by the computer to determine the proper 8K segment of memory to address. Connected to the BUSY output or status line of the printer 3.
Also in CoCo mode, Y18 – Y16 should be 1, all others 0. This is a bit interval timer.