EUROTHERM 2116I PDF

Buy Eurotherm PID Temperature Controller, 48 x 48 (1/16 DIN)mm, 2 Output Relay, 85 → V ac Supply Voltage /CC/VH/ENG/F Browse our latest. Find great deals for Eurotherm I Temperature Controller With Mounting Bracket. Shop with confidence on eBay!. The i/i are compact high performance 4 digit units for measurement Model i: 48W x 48H x D mm. Display: .. Modbus®, Eurotherm ASCII.

Author: Zumi Dozilkree
Country: Italy
Language: English (Spanish)
Genre: Marketing
Published (Last): 26 September 2006
Pages: 73
PDF File Size: 12.85 Mb
ePub File Size: 15.80 Mb
ISBN: 311-9-30269-370-9
Downloads: 86463
Price: Free* [*Free Regsitration Required]
Uploader: Daihn

Read our latest case studies and Successes. Where it is impractical to do this, use shielded cables with the shield grounded at both ends. This is normally alarm 2 or 3. Alarm 2 BBB or to Press change the setpoint. Check input signal High display range exceeded: In addition to the above messages, the displayed process value will flash if the input signal or the displayed value is out of range. Press and together to return to the HOME display. Power Isolation The installation must include a power isolating switch or circuit breaker that disconnects all current carrying conductors.

High alarm 2 has been selected. Press to step across the list headings.

A suitable fuse is EN type T. The display units Display Units 0.

i and i Compact and Economical Indicator & Alarm Unit | Eurotherm by Schneider Electric

Press Press ; D mV input high Press to reach the? O6 Continued in next column A parameter value has been corrupted. Press and to select a parameter in the normal way. Alarm 3 Press or to change the setpoint. Alarm Ack input Logic only D Functions: Under fault conditions such a supply could rise above Vac with respect to ground and the product would not be safe. Other parameters are locked away under password protection. It will go steady when the alarm is acknowledged but still true.

  A LEGACY OF SECRETS CAROL MARINELLI PDF

Eurotherm 2116I Temperature Controller With Mounting Bracket

Only use copper conductors for connections, except thermocouple. Eudotherm information contained in these instructions is subject to change without notice. D Digital output functions. Return for repair Power failure.

If the packaging or the indicator are damaged, do not install the product but contact your nearest Eurotherm Controls agent. Stuck button, or a button was pressed during power up. Refer to the accompanying documents Personnel Electrically conductive pollution for example carbon dust must be excluded from the cabinet in which the indicator is mounted. Isopropyl alcohol may be used to clean labels.

It is called the HOME display.

Alarm 1 is active and it is a Low alarm. The latest release of firmware for the nanodac features batch records. Failure to observe this precaution may damage the indicator or cause some discomfort to the user.

Return for repair Error 3: Process interlocks, including over temperature furnace limits, are implemented using relay outputs. Routing of wires To minimise the pick-up of electrical noise, the sensor input wiring should be 1216i away from high-current power cables.

Gives access to configuration level. The operator interface can be customized to present only those parameters that an operator needs to see and adjust. If, at any time, no key is pressed within 45 seconds, the display will always return to the HOME display. Installation must be carried out by qualified personnel.

  ANTRAG AUF BERUFSAUSBILDUNGSBEIHILFE PDF

Eurotherm 2116 Temperature Controller

General info Description Specification Downloads. The parameter in the N0 list applies a fixed offset over the whole display range. The filter requirements will depend on the type of load. Also terminals 1A and 1B not fitted in indicator only unit. Eurotgerm to software versions 1.

Eurotherm I Temperature Controller With Mounting Bracket | eBay

A universal input enables selection of nine internally stored thermocouple types and the PT resistance thermometer. Reliable performance and accuracy Simple operation Fully configurable using operator interface Alarm blocking on start-up A universal input enables selection of 2116o internally stored thermocouple types and the PT resistance thermometer. O6 0 Having selected a list heading, press within a particular list.

J Alarm 3 is active and it is a Low alarm.

The first character is the alarm setpoint number, the next three the alarm type, as follows: The HOME display will be blank and only alarm messages will be flashed Eutotherm button steps through parameter list headings.

Electrostatic discharge precautions When the indicator is removed from its sleeve, it is vulnerable to damage by electrostatic discharge from someone handling the indicator.