ELIWELL ID970 PDF

Buy Eliwell On/Off Temperature Controller, 74 x 32mm, NTC, PTC Input, 12 V ac/ dc Supply ID Browse our latest on-off-temperature-controllers offers. Buy Eliwell On/Off Temperature Controller, 74 x 32mm, PTC Input, V ac Supply, → +°C Measurement Range ID V 8A+PTC. Browse our. In order to configure the instrument for this purpose you must access the folder identified by the “Add” label and use the parameters “dEA” and “FAA”. ID LX.

Author: Nikozilkree Kazrale
Country: France
Language: English (Spanish)
Genre: Environment
Published (Last): 19 December 2010
Pages: 149
PDF File Size: 16.27 Mb
ePub File Size: 14.84 Mb
ISBN: 205-3-84683-394-6
Downloads: 57285
Price: Free* [*Free Regsitration Required]
Uploader: Yozilkree

The Setpoint value appears on the display. Positive or negative temperature value added to the value read by probe Viewing mode during defrosting. Temperature alarm signal delay time. All the versions are provided with a TTL connection in order to use Copy Card, the quick programming accessory. It is classified as follows: ID Single stage controller for temperature.

The same applies to any elidell or company involved in preparing and writing this document. The sensor has no connection polarity and can be extended using an ordinary bipolar cable note that extending the probe may affect the electromagnetic compatibility EMC of the instrument: Users must not be able eliwdll access parts with dangerous voltage levels under elidell operating conditions. It’s a community-based project which helps to repair anything. For higher loads, use a suitable contactor.

  CATALOGO USAG 2010 PDF

Download from reset Connect the copy card when the instrument is OFF.

Single stage controller for temperature – ID – Eliwell France

The operation cannot be cancelled. When enabled value other than 0it constitutes the access key for level 1 parameters. ID LX Single stage controller for temperature.

Defrost cycles can be controlled at time intervals. In addition, the 16 A compressor relay options and the buzzer are provided.

Eliwell ID970 MC (Milk)

The instrument has screw terminals for connecting electrical cables with a maximum diameter of 2. In normal conditions, the labels for the Set point value is found in the menu. Set point setting folder; -Pb1: Eliwell reserves the right to make any changes or improvements without prior notice and at any time. This means, for example, that an error introduced by the probe is added to any error that is typical of the instrument.

Alarm exclusion time after instrument is switched on following a power failure. At the end of the lamp test, the following messages are displayed for about 5 seconds: Single stage controller for temperature.

For this page to function properly, you must enable JavaScript. Di970 should be noted that the relay contacts supplied with the device are functional and therefore exposed to potential faults. View with decimal point. Drill a 29×71 mm hole, insert a tool and fix it in place with the brackets provided.

Between the request and effective activation of the compressor relay, at least the specified time must elapse. Erasing all parameters ld970 the key. Do not exceed the maximum current allowed. Any protection devices required to comply with product requirements or dictated by common sense due to obvious safety reasons should be installed externally.

  10 BILLION STEPHEN EMMOTT PDF

HSE maximum set cannot be less than LSE minimum set and vice versa Compressor activation time in the event of a faulty probe. Compressor off time in the event of a faulty probe. TTL for connection to Copy Card 3 outputs on relays: Single stage controller for temperature – ID The ID controllers are devices eliwfll for applications on normal or low temperature refrigerating units.

The two sets are interdependent: Single stage controller for temperature ID The password is enabled if the value of the PA1 parameter is not 0.

The continuous improvement of our products can cause some variations in this non contractual document even without notice. The device must be suitably protected from water and dust according to the specific application and only be accessible using special tools except for the front keypad.

Every time the compressor stops, a defrosting cycle is performed according to parameter dty dOH Defrost start delay time from start up of instrument.