ASTM D3183 PDF

This standard is issued under the fixed designation D ; the number 1 This practice is under the jurisdiction of ASTM Committee D11 on. Buy ASTM D Standard Practice for Rubber—Preparation of Pieces for Test Purposes from Products from SAI Global. Buy ASTM D PRACTICE FOR RUBBER – PREPARATION OF PIECES FOR TEST PURPOSES FROM PRODUCTS from SAI.

Author: Shaktilabar Mizragore
Country: Zimbabwe
Language: English (Spanish)
Genre: Finance
Published (Last): 19 November 2016
Pages: 481
PDF File Size: 9.62 Mb
ePub File Size: 7.80 Mb
ISBN: 452-9-13515-671-4
Downloads: 46537
Price: Free* [*Free Regsitration Required]
Uploader: Yozshukora

ASTM D e1. A number in parentheses indicates the year of last reapproval. A superscript epsilon e indicates an editorial change since the last revision or reapproval. This standard has been approved for use by agencies of the Department of Defense.

ASTM D – 02 Standard Practice for Rubber—Preparation of Pieces for Test Purposes from Products

Such pieces are used as a aatm from xstm specimens are obtained for testing. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Procedures are given for preparing pieces suitable for preparing specimens of the product. NOTE 1—For production quality control, testing within 1 to 6 h after vulcanization may be necessary to monitor plant operation. The pieces shall be prepared in accordance with Section 7. The sheets shall be vulcanized in accordance with Practice D and shall have an equivalent state of vulcanization judged from such properties as can be determined on the product.

The sheets shall have one of the following thicknesses unless another thickness is technically necessary: Current edition approved March 30, Originally published as D — Last previous edition D — Preparation of Pieces 7. Procedures in this section describe the preparation of pieces from vulcanizates that are too thick, have uneven surfaces, or contain textiles.

  MALAYALAM MUTHUCHIPPI PDF

If this is not possible, use commercial isooctane. Take care to avoid excessive stretching of the rubber during the separation, by separating a little at a time while the rubber is gripped near the point of separation. If a liquid is used, place the rubber so as to permit free evaporation of the liquid.

Allow time for the complete evaporation of the liquid before the awtm are cut and tested. Some skiving machines can separate plies of rubber as in belts, hose, and tires see 7.

D Standard Practice for Rubber—Preparation of Pieces for Test Purposes from Products

The machine consists of a motor- or hand-driven disk cutter of suitable diameter with a movable cutting table that transports the sample to the cutting satm. An adjustable slow-feed mechanism is? Clamping devices should be available to secure the rubber.

The knife should be lubricated with a mild soap solution to ease the cutting operation. Adjustments should be available to vary the thickness of cut, and feed rollers should be provided to transport the material past the knife.

ASTM D3183 – 10(2015)

Provision should be made for continuous sharpening of the cutting edge. Attachments are available for splitting and cutting sections from cable sheathing and hose.

Uneveness of surface may result from contact with fabric components, cutting techniques, or other reasons.

It is important that the wheel should run true, without vibration, and that the abrasive surface based on aluminum oxide or silicon carbide is true and sharp.

The grinder should be equipped with a slow-feed mechanism so that very light cuts may be made to avoid over-heating of the rubber. Suitable means should be provided for securing the rubber to prevent excessive deformation and for controlled traversing of the rubber pass the abrasive wheel Note 2. In operation the depth of cut should aztm exceed approximately 0.

E3183 successive cuts should be progressively thinner to avoid over-heating. Do not carry out buffing beyond the point where unevenness of thickness has been eliminated.

  IL RICHIAMO DI CTHULHU GDR PDF

For removal of greater thicknesses of rubber, use the cutting techniques indicated in 7. NOTE 2—Wheels of to mm 5 to 6-in. The abrasive bands should be of textile or paper, or a combination of the sstm, with the abradant based on aluminum oxide or silicon carbide bonded to its surface with a resin unaffected by water. Equipment should be provided for slow feeding of the material to the abrasive band and for securing the material without aztm deformation Note 3.

In operation, cuts removing several tenths of a millimetre of rubber are practicable as the heat build up is much lower than with the method of 7.

The buffing may be either against the drum, against one d313 the pulleys, or against the taut band between the pulleys. NOTE 3—Grit sizes 3d183 0. The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own qstm. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.